Product Description
2020年7月17日Product Description: Suitable for charging mobile phone batteries with a capacity of 250-3000mAh and other types of lithium batteries; Can be equipped with USB port output and input characteristics: 1. Built-in high-performance switching power supply, voltage adaptation range: AC 100240V; 2. Suitable input frequency: 5060HZ 3. Allow 50% of inrush current, which is higher than the market average. 4. The insulation resistance is greater than 20M. 5. Low consumption when no-load. The appearance is novel and beautiful, easy to carry and simple to operate. Operation steps: 1) The charger automatically recognizes the polarity, and the built-in intelligent recognition circuit can automatically switch the charger output polarity to suit the battery’s positive and negative poles. 2) Fix the battery: first adjust the positive and negative poles of the battery to adjust the position of the shrapnel (Do not plug in the mains), put the battery so that the battery pole piece and the shrapnel are in good contact. If the LCD display is bright, it means that the battery is in good contact with the charger; if it is not bright, adjust the contact position of the charger shrapnel and the battery until the LCD The screen is bright. visit 3) Charging confirmation: Connect the power supply after fixing the battery. At this time, the LCD display and the battery symbol run back and forth to indicate that it is in the charging state and charging begins. 4) Charging completed: When the charging indicator is completely off and the ’saturation’ indicator is completely on, it indicates that the charging is complete. If it is not urgently used, to ensure the charging effect, continue trickle charging for 12 hours. The extended charging time does not affect the battery use effect. 5) Electrical performance: Applicable battery capacity: 2000mAh Notes: 1. For indoor use only, choose a solid power socket 2. Avoid charging in places where the temperature is high and sun exposure, too high temperature will affect the charging effect and cause charging instructions The lamp does not go off. 3. The charger should cut off the 2industrial plug and socket suppliers20V AC power supply in time when not charging. 4. When charging, the charger shell and the battery shell are slightly hot. It is normal to have a 5. The battery charging indicator may not The light is normal, please continue to recharge the battery. 6. Disposable batteries cannot be charged in the charger, and there is a danger of explosion when the disposable batteries are charged. Generally, the nominal 1.5V batteries (unless indicated) are non-rechargeable batteries. 7. Due to the difference in performance of some batteries, the ’charge’ lamp is still flashing after 12 hours of charging, and the battery is actually fully charged, so the battery can be removed at this time.
?
?
Product Description: Suitable for charging mobile phone batteries with a capacity of 250-3000mAh and other types of lithium batteries; Can be equipped with USB port output and input characteristics:link 1. Built-in high-performance switching power supply, voltage adaptation range: AC 100240V; 2. Suitable input frequency: 5060HZ 3. Allow 50% of inrush current, which is higher than the market average. 4. The insulation resistance is greater than 20M. 5. Low consumption when no-load. The appearance is novel and beautiful, easy to carry and simple to operate. Operation steps: 1) The charger automatically recognizes the polarity, and the built-in intelligent recognition circuit can automatically switch the charger output polarity to suit the battery’s positive and negative poles. 2) Fix the battery: first adjust the positive and negative poles of the battery to adjust the position of the shrapnel (Do not plug in the mains), put the battery so that the battery pole piece and the shrapnel are in good contact. If the LCD display is bright, it means that the battery is in good contact with the charger; if it is not bright, adjust the contact position of the charger shrapnel and the battery until the LCD The screen is bright. 3) Charging confirmation: Connect the power supply after fixing the battery. At this time, the LCD display and the battery symbol run back and forth to indicate that it is in the charging state and charging begins. 4) Charging completed: When the charging indicator is completely off and the ’saturation’ indicator is completely on, it indicates that the charging is complete. If it is not urgently used, to ensure the charging effect, continue trickle charging for 12 hours. The extended charging time does not affect the battery use effect. 5) Electrical performance: Applicable battery capacity: 2000mAh Notes: 1. For indoor use only, choose a solid power socket 2. Avoid charging in places where the temperature is high and sun exposure, too high temperature will affect the charging effect and cause charging instructions The lamp does not go off. 3. The charger should cut off the 220V AC power supply in time when not charging. 4. When charging, the charger shell and the battery shell are slightly hot. It is normal to have a 5. The battery charging indicator may not The light is normal, please continue to recharge the battery. 6. Disposable batteries cannot be charged in the charger, and there is a danger of explosion when the disposable batteries are charged. Generally, the nominal 1.5V batteries (unless indicated) are non-rechargeable batteries. 7. Due to the difference in performance of some batteries, the ’charge’ lamp is still flashing after 12 hours of charging, and the battery is actually fully charged, so the battery can be removed at this time. Product Description: Suitable for charging mobile phone batteries with a capacity of 250-3000mAh and other types of lithium batteries; Can be equipped with USB port output and input characteristics: 1. Built-in high-performance switching power supply, voltage adaptation range: AC 100240V; 2. Suitable input frequency: 5060HZ 3. Allow 50% of inrush current, which is higher than the market average. 4. The insulation resistance is greater than 20M. 5. Low consumption when no-load. The appearance is novel and beautiful, easy to carry and simple to operate. Operation steps: 1) The charger automatically recognizes the polarity, and the built-in intelligent recognition circuit can automatically switch the charger output polarity to suit the battery’s positive and negative poles. 2) Fix the battery: first adjust the positive and negative poles of the battery to adjust the position of the shrapnel (Do not plug in the mains), put the battery so that the battery pole piece and the shrapnel are in good contact. If the LCD display is bright, it means that the battery is in good contact with the charger; if it is not bright, adjust the contact position of the charger shrapnel and the battery until the LCD displays The screen is bright. 3) Charging confirmation: Connect the power supply after fixing the battery. At this time, the LCD display and the battery symbol run back and forth to indicate that it is in the charging state and charging begins. 4) Charging completed: When the charging indicator is completely off and the ’saturation’ indicator is completely on, it indicates that the charging is complete. If it is not urgently used, to ensure the charging effect, continue trickle charging for 12 hours. The extended charging time does not affect the battery use effect. 5) Electrical performance: Applicable battery capacity: 2000mAh Notes: 1. For indoor use only, choose a solid power socket 2. Avoid charging in places where the temperature is high and sun exposure, too high temperature will affect the charging effect and cause charging instructions The lamp does not go off. 3. The charger should cut off the 220V AC power supply in time when not charging. 4. When charging, the charger shell and the battery shell are slightly hot. It is normal to have a 5. The battery charging indicator may not The light is normal, please continue to recharge the battery. 6. Disposable batteries cannot be charged in the charger, and there is a danger of explosion when the disposable batteries are charged. Generally, the nominal 1.5V batteries (unless indicated) are non-rechargeable batteries. 7. Due to the difference in performance of some batteries, the ’charge’ lamp is still flashing after 12 hours of charging, and the battery is actually fully charged, so the battery can be removed at this time.
?
?
Product Description: Suitable for charging mobile phone batteries with a capacity of 250-3000mAh and other types of lithium batteries; Can be equipped with USB port output and input characteristics:link 1. Built-in high-performance switching power supply, voltage adaptation range: AC 100240V; 2. Suitable input frequency: 5060HZ 3. Allow 50% of inrush current, which is higher than the market average. 4. The insulation resistance is greater than 20M. 5. Low consumption when no-load. The appearance is novel and beautiful, easy to carry and simple to operate. Operation steps: 1) The charger automatically recognizes the polarity, and the built-in intelligent recognition circuit can automatically switch the charger output polarity to suit the battery’s positive and negative poles. 2) Fix the battery: first adjust the positive and negative poles of the battery to adjust the position of the shrapnel (Do not plug in the mains), put the battery so that the battery pole piece and the shrapnel are in good contact. If the LCD display is bright, it means that the battery is in good contact with the charger; if it is not bright, adjust the contact position of the charger shrapnel and the battery until the LCD The screen is bright. 3) Charging confirmation: Connect the power supply after fixing the battery. At this time, the LCD display and the battery symbol run back and forth to indicate that it is in the charging state and charging begins. 4) Charging completed: When the charging indicator is completely off and the ’saturation’ indicator is completely on, it indicates that the charging is complete. If it is not urgently used, to ensure the charging effect, continue trickle charging for 12 hours. The extended charging time does not affect the battery use effect. 5) Electrical performance: Applicable battery capacity: 2000mAh Notes: 1. For indoor use only, choose a solid power socket 2. Avoid charging in places where the temperature is high and sun exposure, too high temperature will affect the charging effect and cause charging instructions The lamp does not go off. 3. The charger should cut off the 220V AC power supply in time when not charging. 4. When charging, the charger shell and the battery shell are slightly hot. It is normal to have a 5. The battery charging indicator may not The light is normal, please continue to recharge the battery. 6. Disposable batteries cannot be charged in the charger, and there is a danger of explosion when the disposable batteries are charged. Generally, the nominal 1.5V batteries (unless indicated) are non-rechargeable batteries. 7. Due to the difference in performance of some batteries, the ’charge’ lamp is still flashing after 12 hours of charging, and the battery is actually fully charged, so the battery can be removed at this time. Product Description: Suitable for charging mobile phone batteries with a capacity of 250-3000mAh and other types of lithium batteries; Can be equipped with USB port output and input characteristics: 1. Built-in high-performance switching power supply, voltage adaptation range: AC 100240V; 2. Suitable input frequency: 5060HZ 3. Allow 50% of inrush current, which is higher than the market average. 4. The insulation resistance is greater than 20M. 5. Low consumption when no-load. The appearance is novel and beautiful, easy to carry and simple to operate. Operation steps: 1) The charger automatically recognizes the polarity, and the built-in intelligent recognition circuit can automatically switch the charger output polarity to suit the battery’s positive and negative poles. 2) Fix the battery: first adjust the positive and negative poles of the battery to adjust the position of the shrapnel (Do not plug in the mains), put the battery so that the battery pole piece and the shrapnel are in good contact. If the LCD display is bright, it means that the battery is in good contact with the charger; if it is not bright, adjust the contact position of the charger shrapnel and the battery until the LCD displays The screen is bright. 3) Charging confirmation: Connect the power supply after fixing the battery. At this time, the LCD display and the battery symbol run back and forth to indicate that it is in the charging state and charging begins. 4) Charging completed: When the charging indicator is completely off and the ’saturation’ indicator is completely on, it indicates that the charging is complete. If it is not urgently used, to ensure the charging effect, continue trickle charging for 12 hours. The extended charging time does not affect the battery use effect. 5) Electrical performance: Applicable battery capacity: 2000mAh Notes: 1. For indoor use only, choose a solid power socket 2. Avoid charging in places where the temperature is high and sun exposure, too high temperature will affect the charging effect and cause charging instructions The lamp does not go off. 3. The charger should cut off the 220V AC power supply in time when not charging. 4. When charging, the charger shell and the battery shell are slightly hot. It is normal to have a 5. The battery charging indicator may not The light is normal, please continue to recharge the battery. 6. Disposable batteries cannot be charged in the charger, and there is a danger of explosion when the disposable batteries are charged. Generally, the nominal 1.5V batteries (unless indicated) are non-rechargeable batteries. 7. Due to the difference in performance of some batteries, the ’charge’ lamp is still flashing after 12 hours of charging, and the battery is actually fully charged, so the battery can be removed at this time.
コメント